Beta Firmware available with Chlorinator Support

autelis
Site Admin
Posts: 1123
Joined: Tue Nov 30, 2010 1:02 pm

Re: Beta Firmware available with Chlorinator Support

Post by autelis » Fri Jul 03, 2015 9:51 am

No the previous setting should be saved between reboots. We were not able to reproduce this problem. Can you provide the steps necessary to reproduce it?
Autelis.com Staff
RRoyceus
Posts: 40
Joined: Sat May 30, 2015 6:39 pm

Re: Beta Firmware available with Chlorinator Support

Post by RRoyceus » Sat Jul 04, 2015 10:23 am

I may have determined the problem. I wanted to set up network resources to change the chlorination level. I probably set it up wrong. I used the statement: GET /chlor.cgi?pool=50 HTTP/1.1

What would the correct statement be?
autelis
Site Admin
Posts: 1123
Joined: Tue Nov 30, 2010 1:02 pm

Re: Beta Firmware available with Chlorinator Support

Post by autelis » Mon Jul 06, 2015 11:10 am

That command is correct to set the chlorination to 50%. You can either create additional commands for other percentages or you can use a substitution variable in your ISY network resource and then set the variable before triggering the command.

Thanks
Autelis.com Staff
RRoyceus
Posts: 40
Joined: Sat May 30, 2015 6:39 pm

Re: Beta Firmware available with Chlorinator Support

Post by RRoyceus » Sat Aug 15, 2015 6:35 pm

The software has been working well. My salt cell went out last week. I have replaced it with a new cell. The current reading is 3200. I had it tested at the pool store today, they showed 3000. In either case, not high. I noticed today that the chlorination page has an alternating message, high current.

Is this a problem? Any suggestions?
autelis
Site Admin
Posts: 1123
Joined: Tue Nov 30, 2010 1:02 pm

Re: Beta Firmware available with Chlorinator Support

Post by autelis » Mon Aug 17, 2015 9:03 am

Thanks for your post. If you check the actual current values at the chlorinator when you see the error, you should be able to tell whether the current is out of range. Unfortunately these error codes are not fully documented so we cannot guarantee how accurate or useful they may be.

Thanks
Autelis.com Staff
CapSean
Posts: 1
Joined: Sun Aug 14, 2016 10:18 am

Re: Beta Firmware available with Chlorinator Support

Post by CapSean » Sun Aug 14, 2016 10:22 am

Hello, I would like to try the firmware. Please send URL and instructions? Thank you very much.
autelis
Site Admin
Posts: 1123
Joined: Tue Nov 30, 2010 1:02 pm

Re: Beta Firmware available with Chlorinator Support

Post by autelis » Mon Aug 15, 2016 12:52 pm

CapSean wrote:Hello, I would like to try the firmware. Please send URL and instructions? Thank you very much.
We sent you an email. Thanks.
Autelis.com Staff
Giomania
Posts: 4
Joined: Thu Sep 22, 2016 11:40 am

Re: Beta Firmware available with Chlorinator Support

Post by Giomania » Fri May 19, 2017 9:00 am

Would you please send me the beta firmware?

Thanks.

Mark
RRoyceus
Posts: 40
Joined: Sat May 30, 2015 6:39 pm

Re: Beta Firmware available with Chlorinator Support

Post by RRoyceus » Fri May 29, 2020 3:27 pm

I have been using this since it was released and really like it. Up until now I have been using it with my ISY994i only to start and stop my pump on a schedule and using a http comand set.cgi? This week I tried to use it using the http command pump.cgi?num=1&val=0 to change the speed on my pump without success.

Can anybody tell me the correct http command to change the speed?
Post Reply