Pool Control for Jandy/Zodiac PDA
Welcome to the Product Page for Pool Control for Jandy/Zodiac PDA
- 1 About this product
- 2 Screenshots
- 3 Downloads
- 4 Installation
- 5 Web Interface
- 6 Mobile Web App
- 7 Emergency Factory Reset / Forgotten Password
- 8 Compliance Information
About this product
Pool Control for Jandy®/Zodiac® PDA is designed to link your Jandy®/Zodiac® Aqualink® PDA powered pool to your network and provide a remote control interface over the web and through various mobile devices.
NOTE: You can still use your existing PDA controller, but only one device may be active at a time. Both the PDA and the Autelis Pool Control will automatically become inactive after a certain period of inactivity.
Disclaimer: All trademarks referenced herein are the property of their respective owners. This product is not affiliated with or endorsed by Jandy Industries, Inc., Zodiac International, S.A.S.U., or its affiliates in any way.
Hardware Model XN200 (current): Length: 5.1 inches, Width: 4.75 inches, Height: 1.5 inches, 2x 0.125 inch mounting holes 6.4 inches apart centered on Width
Hardware Models BN100 & SN100: Length: 4.88 inches, Width: 2.23 inches, Height: 1.59 inches
Please choose the right firmware for your device model.
Pool Control (PC100JZPDA)
Version 1.0.2 Update - Fix for Systems w/ Firmware 3.0 or Newer
Current software version: 1.0.2
The Autelis Pool Control is compatible with Aqualink® PDA systems.
This product is designed for indoor installation and the enclosure supplied is not waterproof.
If your system wiring is vulnerable to power surges caused by lightning strikes then installing a lightning isolation device is recommended. Damage due to lightning surges is not covered under the product warranty.
The Autelis Pool Control interfaces directly to your existing system and does not require any additional interface or protocol adapters. Installation requires connection to the 4-wire equipment bus on your Aqualink® system. This 4-wire bus connects all the keypads and control devices in your system to the main control center. You can connect to the bus either at the control center or at a keypad location. Please refer to the installation manual for your Aqualink® system for more information on connecting keypads and accessory equipment to the bus and be sure to follow all safety procedures described therein. Once you have familiarized yourself with the Aqualink® hardware and turned off the power to the system, follow the diagram on the label on the bottom of your device to match the labels on the 4-wire connector with the correct bus wires which are designated by color (Green, Yellow, Black, Red).
Connection to Network
Installation requires connection to your network router or switch which supports 10Base-T Ethernet. Connect the built-in ethernet port to your network device using the included cat-5 cable or a standard cat-5 networking cable of your choice. You may also use a wireless bridge or a Powerline network device to provide the network connection. The Pool Control device will obtain an IP address automatically via DHCP.
Connection to Power
Connect the included power adapter to the device and plug it into a standard wall outlet. When plugged in, the green LED on the ethernet port will blink for 5 seconds and then the device will boot normally.
You can look for Pool Control in Windows under your list of uPnP Network devices. Double click on it to launch the web page. You may not see it listed there depending on your uPnP settings. You can also try accessing the web interface by typing 'http://poolcontrol' into your browser. This may not work with all routers and network configurations (see below hint). You can also type the IP address of the Pool Control device which can be found in your router interface by matching an IP address from the table with the MAC address printed on the bottom of the device or by using an IP scanner tool to search by MAC address. Log in using the username 'admin' and the default password 'admin'.
Windows Hint: In your network connection properties under TCP/IPv4 properties, click the advanced button. In the DNS tab, select "Append these DNS suffixes (in order)" and click add and enter "." (a single period with no quotes).
This page displays basic system information.
- Software Version
- The software version of the Autelis Pool Control device. This information is not related to the Aqualink® software version.
- The current time value from the Autelis Pool Control device, adjusted for your computer's local time settings. This information is not related to the time kept by the Aqualink® system.
- Clicking this button will reboot the Autelis Pool Control device. It will not reboot the Aqualink® system.
- Clicking this button will reset all settings to factory defaults (including password) and reboot the device. It will not change any settings on or reboot the Aqualink® system.
The keypad interface gives you the PDA style control you are used to in your web browser.
The keypad can be controlled using your mouse to click the buttons on the screen or by using your keyboard. The available actions and their associated keyboard keys are listed below.
Move Up - Up Arrow, Number Pad 8 Move Down - Down Arrow, Number Pad 2 1 - Number Pad 1, 1 2 - Number Pad 3, 3 Back - Left Arrow, Number Pad 4 Select - Right Arrow, Number Pad 5, Number Pad 6, Enter, Spacebar
Mobile Web App
The built-in mobile web app can be accessed from any browser including iPhone, iPad, and Android devices.
To launch the web app, visit http://poolcontrol/app.html or http://ip.address.here/app.html
The app allows you to save your password so that you do not need to log in every time you visit it. This is especially useful when adding the app to your home screen on iOS devices. To save your password, load the app and click on the settings button in the top right corner. Then enter your password and click "Save". To clear your saved password, click "Clear".
The up and down buttons are activated by clicking on the top or bottom half of the text display. Use the OK and Back buttons to navigate through menus. Press the 1 or 2 button to activate the assigned hotkey functions.
Emergency Factory Reset / Forgotten Password
In the event you have forgotten your password, you will need to factory reset your device. To do this, go to http://poolcontrol/userreset.cgi?do=true or http://ip.address.here/userreset.cgi?do=true in your web browser and enter the username "admin" and for the password enter the security key printed on the label on the bottom of your device. The security key can only be used to factory reset the device and will not allow you to access any other web pages.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment and receiver.
- - Connect the equipment into an output on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radio/TV technician for help.